Yamaha r1 service manual 2009. 2009 2011 yamaha yzfr1 service repair workshop manual download (2009 … 2019-01-25

Yamaha r1 service manual 2009 Rating: 5,8/10 1989 reviews

Yamaha R1 2009 Service Manual

yamaha r1 service manual 2009

Route the throttle cable above the under bracket, inside of the front fork and under the brake fluid reservoir hose. Prior to adjusting the throttle cable free play, the engine idling speed and carburetor synchronization should be adjusted properly. When pinching, make sure not to change the shape of the hook. For installation, reverse the removal procedure. Measure the valve clearance 2 and 4 with a thickness gauge. For installation, reverse the removal procedure.

Next

Reading : 2009 Yamaha R1 Service Manual

yamaha r1 service manual 2009

Fasten the front brake hose to the right front fork leg with the plastic locking tie. Install: Front brake calipers b. Therefore, keep the drive chain slack within the specified limits. Symbols 5 indicate parts to be lubricated or replaced. Therefore, always clean up any spilt brake fluid immediately. Lean angle sensor lead 9. Tighten the bolt to 25 Nm 2.

Next

YAMAHA ’09 YZF

yamaha r1 service manual 2009

When installing the rear brake caliper bracket, make sure to fit the torque receptor convex of the rear brake caliper bracket and torque receptor groove of the swingarm. Tighten the new oil filter cartridge to specification with an oil filter wrench. Average fuel consumption mode 1. Check: Engine for engine oil leaks 2. Route the main harness outside of the radiator inlet pipe. Remove: Cap bolt 1 from the damper adjusting rod Spacer 2 Nut 3 a.

Next

Yamaha YZF

yamaha r1 service manual 2009

After Step K as above is finished, check that the connector is completely attached by sliding the double lock orange part d on the connector as shown in the illustration and seeing if it touches firmly or not. I keep hearing January but its about over. Did I not show the moose is the lumb ox? Slide the upper tail cover forward and remove. Check: Lead Coupler Connector Moisture Dry with an air blower. Apply a thin coat of rubber adhesive onto the end of the left handlebar.

Next

2009 2011 yamaha yzfr1 service repair workshop manual download (2009 …

yamaha r1 service manual 2009

Make sure that the pin is flush with the fasteners head. Jobs 7 requiring more information such as special tools and technical data are described sequentially. Turn the adjusting screw 1 in direction a or b. Electronic control throttle systems have been used on automobiles, but Yamaha has developed a faster, more compact system specifically for the needs of a sports motorcycle. Since these spark plugs have a copper gasket, caution is needed during installation on the following points.

Next

2009 R1 Service Manual @ R1

yamaha r1 service manual 2009

Install: Rear view mirror 1 along with the mirror base 2 Rear view mirror nut 7 Nm 0. Oil cooler outlet hose A. During reassembly, properly oil all mating parts and bearings and lubricate the oil seal lips with grease. Route the headlight lead toward the front of the meter bracket and connect. For installation, reverse the removal procedure. Contact should be made only with the outer race 6. The injection timing is determined through the signals from the crankshaft position sensor.

Next

Yamaha YZF R1 Y service Workshop Service Repair Manual

yamaha r1 service manual 2009

Brake fluid may damage painted surfaces and plastic parts. Install the exhaust and intake camshafts, timing chain and camshaft caps. Make sure to pass the brake hose through the brake hose holder. When to tighten the cap bolt to the specified torque is after installing the front fork leg to the vehicle and tightening the lower bracket pinch bolts. The auxiliary light lead should not be pinched when installing the air intake air duct cover. Turn the crankshaft clockwise and align the pickup rotor K mark a and crankcase occluding surface b. Check operation and replace if necessary.

Next

2009 Yamaha YZF

yamaha r1 service manual 2009

Check: Rear brake pad Wear indicators 1 almost touch the brake disc Replace the brake pads as a set. Right air intake air duct cover 11. I did not look the technical term used for Yam's second fiddle on the R1. . Install: Brake master cylinder holder 1 Front brake master cylinder holder bolt 13 Nm 1. Measure: Spring free length a Out of specification Replace. Stand the vehicle on a level surface.

Next

2009 Yamaha YZF

yamaha r1 service manual 2009

Check: Tire pressure Out of specification Regulate. Make a note of the position of each valve lifter 1 and valve pad 2 so that they can be installed in the correct place. Stand the vehicle on a level surface. Disconnect: Coolant reservoir cap 1 4. Nut and cap bolt 25 Nm 2. Fit it inside of the console panel.

Next