Use only the proper tools and cleaning equipment. If there is any dealer inspect the brake system. Use of fuel stabilizer and conditioner eliminates the need to drain the fuel system. Apply a rust preventive lubricant to the threads on both sides of the rear axle and to the wheel hub surfaces that contact the rear axle washers. Could cause you to react more slowly. If there is free play, have a Yamaha the brakes firmly for one minute. Wear indicator groove Front 1.
Otherwise your feet may contact the rear wheels. A number that is enclosed by a circle indicates a disassembly step. Ê Install the headlight relay, then the radiator fan motor relay, onto the tab on the rear fender. Lower grease nipple ×2 8-43. If your machine injury or property damage. H Apply engine oil I Apply gear oil J Apply molybdenum disulfide oil K Apply wheel bearing grease L Apply lithium-soap-based grease M Apply molybdenum disulfide grease Symbols N to O in the exploded diagrams indicate where to apply a locking agent N and when to install a new part O. Do not turn at excessive speed.
Print what you need when you need it! Tightening torque: Oil filter element cover bolt: 10 Nm 1. Reservoir tank cap Observe these precautions: 8 When checking the brake fluid level, make sure the top of the brake fluid reservoir is level. When the movement of the brake caliper piston and the nut is greater than the backlash of the threads of the nut and the adjusting bolt, the force È will be required to pull the adjusting bolt. If necessary, apply inches in depth. It represents the result of many years of Yamaha experience in the production of fine sporting, touring, and pacesetting racing machines. Before riding, check that the brake fluid is above the minimum level mark and replenish if neces- sary. The transmission allows Improperly operating in reverse.
Start the engine, warm it up for several hole to raise it to the correct level. Tighten the locknut on the brake cable. If the fuse immediately blows again, consult a Yamaha dealer. Headlight bulb holder cover 2. You should periodically remove and inspect the spark plug because heat and deposits will cause the spark plug to slowly break down and erode. Yamaha Raptor Repair Manual Yamaha Raptor Service Manual Yamaha Raptor Shop Manual. Riding on public roads can result in collisions with other vehicles.
Use only the appropriate special tools; this will help prevent damage caused by the use of inappropriate tools or improvised techniques. Com-ponents should be at room temperature. The engine is warm when it 1. If room to do so by steering in the direction of the unexpected and uncorrected, sliding could lead slide. The injection timing is determined through the signals from the crankshaft posi-tion sensor.
If it does not 1. After the bolt or nut has been tightened to specification, bend the lock tabs along a flat of the bolt or nut. Push down on the pedal to apply the rear brake. Remove the spark plug cap. Inspect the sponge material and replace it oughly in solvent. At this time, the clutch torque Ê between the adjusting bolt and the adjusting bolt sleeve 4 will decrease depending on the force required to pull the adjusting bolt. Adjust the spring preload as follows.
Remove the battery and charge it. The amount of the adjustment varies with brake fluid pressure. Remove the nuts from the wheel. Record the information on this label in the space provided. Ì Make sure that there is no slack in the wire har-ness in the area shown in the illustration. A special wrench can be obtained at a Yamaha dealer to make this adjustment. This information will be needed to order spare parts from your Yamaha dealer.
Dismount on the uphill side or to a side if pointed straight uphill. In addition, the oil must be changed back into the filler hole without screwing it and the oil filter element replaced at the intervals in , and then remove it again to check the. Turn the adjusting nut while holding the rear brake light switch in place. Covers the entire vehicle from front to back, its the same type of Manual that is used by Professional Mechanics to service or repair your vehicle. Riding on paved surfaces can cause loss of con- trol. Opening the throttle abruptly or releasing Be sure that the engine has sufficiently slowed the clutch lever too quickly.
Ë Route the negative battery lead between the lean angle sensor and the wire harness. Î Fasten the oil tank outlet hose and reverse con-trol cable with the clamp, making sure that the reverse control cable does not contact the edge of the engine stay. A: Distance between flats B: Outside thread diameter Ex. Loosen the locknut at the crankcase side. Remove the defective bulb and replace it 4. If necessary, adjust the brake light switch as follows.
These procedures should be performed by a Yamaha dealer. Operating with improperly adjusted brakes. Û Route the front brake light switch lead behind the front brake hose and throttle cable. All air must be bled from the brake sys- tem. Tighten the rear axle pinch bolts in the Lubricating the drive chain order shown to the specified torque. Ê Install the radiator inlet hose with its white paint mark facing outward.